ACYBOND™ 3300LT

新一代高综合性能水性丙烯酸树脂

---- 专为高性能的透明底面漆设计的高性价比水性树脂

ACYBOND™ 3300LT 丙烯酸聚合乳液在水性木器漆及水性工业漆领域应用广泛，性能稳定优异，采用核壳结构的乳液自交联技术，其核硬壳软的结构设计（核的玻璃化温度大于50℃，壳的玻璃化温度小于0℃）从而形成高硬度、高抗粘，优秀的打磨性能的特性。在核壳合成过程中，采用包括加成有机硅在内的双重交联技术，使树脂在硬度、耐水性、附着力、光泽等方面得到更大提高，硬度与水性聚氨酯相仿，漆膜具有优秀的清透性。

ACYBOND™ 3300LT 的特点：

干燥速度快，漆膜在常温下表干快，硬度上升快，打磨性能上升快；

环保无毒，不含APEO，不含甲醛；

优秀的漆膜透明度；

优异的光泽，可以设计高光配方；

抗粘连性好；

优秀的附着力；

用于松木耐黄变性能好；

防涨茎性能好；

 典型物理性质:

ACYBOND™ 3300LT

New Generation Acrylic Co-polymerr

---- Special design for high performance and low price waterborne wood coatings

ACYBOND™ 3300LT emulsion was designed for use in factory-applied, waterborne interior wood coatings. It offers good early sandability, block resistance and stain resistance, as well as extremely low microfoam entrapment. It was designed for Core-shell emulsion (core hard Tg > 50 ºC  and soft shell Tg < 0 ºC) and self-crosslinking technical. It offers excellent surface hard as well as good low temperature film grow up. It has water resistance, good adhesion to substrate was used in water base wood coating.

ACYBOND™ 3300LT characteristic：

Quick hardness development;

Outstanding membrane clear clarity；

Dry fast, Excellent preliminary stage sanding;

Excellent preliminary stage Anti-stick under board to board;

APEO free and no added formaldehyde or formaldehyde generators;

Good application properties;

Good gloss potential;

 Special physical data:

物料安全技术手册

1. 物料与厂商资料

物品名称：水性丙烯酸乳液

物品牌号：ACYBOND 3300LT

供应商资料：广州市祥枫化工科技有限公司/中国广州市天河区东圃镇东圃商业大厦D座3A17室/联系电话：86-020-62861313/传真：86-020-62861326/电邮：SAILORZENG@ALIYUN.COM/联系人：曾杰

2.成分资料

所属化学类别：水性丙烯酸聚合物

分子形态：高分子聚合物

组份：  1）丙烯酸共聚物：42% ，化学物质登记号码（CAS NO）: 25085-34-1；

2）水： 58%, 化学物质登记号码（CAS NO）: 7732-18-5

3.危害辨识资料

允许接触限度：无相应限制。该产品不是危险品。

物品危害分类：第9类

4.急救措施

1）皮肤接触：尽快脱去被污染的衣物，鞋子，用水反复清洗，冲洗后还有刺激，立即就医。

2）眼睛接触：立即将眼皮撑开，用水反复缓和冲洗至少10分钟，不要让含有污染物的冲洗水流入未受污染的眼睛里，冲洗后还有刺激感，立即就医。

3）吸入:出去污染源将患者移到空气新鲜处，多休息，如呼吸困难，由受过训练的人供给氧气，如果还有症状立即就医。

4）食入：清洗嘴巴，立即就医

5.灭火措施

不是易燃物品，万一陷入火中，可能释放有毒害或有刺激性气味的气体。

适用灭火器：泡沫，干粉，二氧化碳，水枪

禁止使用何种灭火器：没有

特别暴露危害：万一发生火灾或者爆炸，不要呼吸所释放的气体

保护装备：火灾中该产品能够释放有毒害的气体，穿戴呼吸保护装备

特殊防备：用水冷却未泄露的包装，防止包装压力增加

6.泄露处理

个人注意事项：预防接触眼睛和皮肤

环境注意事项：围堵泄露物不要扩散，用干砂土吸收，保持环境通风，避免泄露物进入下水道和密闭的空间

清理方法：用沙，土和任何可以吸收的物料进行吸收，再包装掩埋。

7.安全处置和储存方法

处置预防：避免在不通风的环境下开通；避免物料的挥发浓缩；避免吸入挥发气体；避免眼睛和皮肤接触

储存预防：远离高温和霜冻，储存在5-40度阴凉，干燥，通风良好及阳光无法直射的地方。

8.暴露预防措施

暴露控制：避免接触皮肤和眼睛，避免吸入挥发物，在通风处使用

个人防护保护：佩戴呼吸口罩，特别在喷涂中使用

手部保护：安全手套

眼睛保护：安全眼镜

皮肤保护：安全着装

9.物理及化学性质

外观：乳白色液体

挥发率 (重量百分比)：58% (水)/粘度：50-400CPS /挥发速度：(WATER=1) 1  /pH ：7.0-9.0

水溶性：100% 可溶  /密度：1.03

可燃性数据：该产品不可燃；闪点： 不适用；爆炸上限：不适用；爆炸下限：不适用；自燃温度：不适用

灭火介质：液态物质不可燃。 成膜干燥后可燃烧。可使用任何灭火介质来扑灭该物质引起的火灾。

灭火注意事项：无特别要求

10.安定性及反应性

安定性：正常状况下安定，不发生反应，水汽挥发完会成膜或粉

预防避免的状况：没有

预防避免的物料：没有

危害分解物：没有

11.毒性资料

吸入物：引起呼吸系统刺激

皮肤：对皮肤有刺激

眼睛：对眼睛有刺激

食入：对胃肠有危害

长时间暴露：无

12.生态资料

可能的环境影响：如果没有化学成膜，不要释放到环境中，成膜物对环境没有危害

其他相关数据：-风险评估，对水有轻微的危害: (VwVwS 4.3; 17.05.1999)

13.废弃处置办法

参照当地的法律法规处理

14.运输资料

非危险品，不受条例管制

15.调整资料

适用法规：劳动者安全与卫生；危险品管理与储存守则；危险品运输；废弃物储存清除处理方法及设施标准

产品分级：无

危险划分：无

安全划分：无

无EC的*：无

MATERIAL SAFETY DATA SHEET

1. IDENTIFICATION OF THE SUBSTANCE/PREPERATION AND THE COMPANY

VERSION DATE: 2015-4-4

Product Name : ACYBOND 3300LT

Chemical Name: Acrylic co-polymer

Company Information:Guangzhou CONFON Chemical Tec. Co., Ltd.    Emergency:

Room3A17,Dongpu Business Plaza , Tel:020-62861313

Tianhe , Guangzhou, P.R.C.                          Fax:020-62861326

SAILORZENG@ALIYUN.COM

2. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Characterization: Waterborne copolymer CAS No. :  -

Conc. wt%                              Casnr.       Hazard Symbols     R-phrases

Conc. wt%               CAS NO

42% acrylic copolymer 25085-34-1

58% Water                 7732-18-5

3. HAZARDS IDENTIFICATION

This health hazard assessment is based on a consideration of the composition of this product.

May cause eye irritation.

4. FIRST AID MEASURES

Skin Contact: Remove contaminated clothing. Wash skin with water. If symptoms develop, obtain medical attention.

Eye Contact: Irrigate with eyewash solution or clean water, holding the eyelids apart, for at least 10 minutes. Obtain medical attention if ill effects occur.

Inhalation: Remove the patient from exposure, keep warm and at rest. Obtain medical attention if ill effects occur. 

Ingestion: Wash out mouth with water. Obtain medical attention if ill 

effects occur.

Further medical treatment: Symptomatic treatment and supportive therapy as indicated.

5. FIRE-FIGHTING MEASURES

Not classed as flammable. If involved in a fire, it may emit noxious and toxic fumes.

Extinguish media: Foam, CO2, dry powder, water spray.

Don't use: -

Special exposure hazards: In case of fire and/or explosion do not breathe fumes.

Protective equipment: Product may give off toxic fumes in fire: wear breathing apparatus

Special precautions: Water may be used to cool closed containers to prevent pressure build-up.

6. ACCIDENTAL RELEASE MEASUREMENT

Personal precautions: Avoid contact with skin and eyes.

Environmental precautions: Do not release to the environment.

Methods for cleaning up: Absorb spillages in sand, earth or any suitable absorbent material. Transfer to a container for disposal. 

7. HANDLING AND STORAGE

Handling precautions Avoid opening drums in unventilated areas to avoid 

concentrated vapours. Avoid breathing vapours. Avoid contact with skin and eyes. 

Storage conditions Keep away from frost.

Store between 5°C and 40°C. 

8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Exposure controls: Avoid contact with skin and eyes. Do not breathe vapour/spray. Use only in well ventilated areas. Do not take internally. 

Personal protection equipment

Respirators protection yes, (in spray mists)

Hands protection gloves

Eyes protection safety glasses.

Skin protection     safety wear. 

9. PHYSICAL AND CHEMICAL PROPERTIES

Type waterborne acrylic copolymer 

Appearance   white liquid

Odor Mild

pH 7.0 – 9.0

Boiling point ± 100 ºC 

Total solids (%w/w) 42 ± 1 %

Viscosity Brookfield (25ºC) 50-400 mPas 

Density (20 ºC; kg/l) 1.03

Solubility in water (% by wt.) Miscible.

Vapor pressure (at 20℃) 23 mbar as water

Flashing point     Not applicable

Explosion Limited           Not applicable

Oxidizing properties Not applicable

Flammability Not applicable

Softening point Not applicable

Melting point Not applicable

10. STABILITY AND REACTIVITY

Stability The material will not support combustion unless the water has evaportaed

Conditions to avoid None known

Material to avoid None known

Hazardous decomposition products None known

11. TOXICOLOGICAL INFORMATION

Inhalation: May be irritating to respiratory system

Skin: May cause skin irritation

Eyes: May cause eye irritation

Ingestion: May be harmful if swallowed

Long time exposure No information available

12. ECOLOGICAL INFORMATION

Ecotoxicity Do not release to the environment without chemical

precipitation/flocculation. The precipitate is not hazardous.

 Other relating data: -

WGK: 1: slightly hazardous to water (VwVwS 4.3; 17.05.1999)

13. DISPOSAL CONSIDERATIONS

Dispose in accordance with local and state regulations.

14. TRANSPORT INFORMATION

Not classified as hazardous for transport

DOT classification no regulation

IATA/ICAO classification -

Packing Group -

UN number -

“Marine pollutant” no

"Proper shipping name" NOT RESTRICTED

Additional information   -

15. REGULATORY INFORMATION

Classification NOT CLASSIFIED AS HAZARDOUS TO USERS

Risk Phrases   -

Safety Phrases   -

Non EC Countries   -

The information contained in this safety data sheet is the result of the most up-to-data available in our company. The information given in this data sheet does not constitute or replace the user’s own assessment of workplace risk as required by other health and safety legislation. The user must ensure that the information is suitable and complete in relation to the specific use of the product

Acybond 3300LT推荐配方

水性透明底漆

水性透明面漆